Consequence: The driver may notice fuel odor, drivability concerns such as hesitation, misfire, stalling, rough running, or difficulty in starting and the 'check engine' light may be illuminated. Please rate my answer so I an awarded points for it. Then remove the ballast using a philip screwdriver. . We stock headlight parts for most Land Rover models including , , and. Push on this tab and pull the cover down to expose the bulbs.
Best practice is to ship to a friend or family in the Continental U. Line up the tabs on the headlight assembly to the slots in the headlight housing in the fender and push the whole thing in. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. It may take a bit of a push because there is some gooey adhesive between the headlight and the fender. This is a quality, recycled 2005 Land Rover Lr3 Headlamp Assembly. I broke one of them before realizing this. This part can ship anywhere within the Continental United States with FedEx Ground.
For the black tabs, it is a two-piece fastener, just pull up on the small center post, it will release the expanding part below the plate. Consequence: If the srs warning light is ignored and a vehicle crash of sufficient severity to command deployment of the driver's air bag occurs, the air bag module may not deploy in the intended manner. Call toll free to order or place your order online via our secure checkout system. Please rate my answer so I an awarded points for it. You'll have to check for voltage at the bulb socket when the low beam headlights are turned on. Remove the old bulb from the socket by firmly, but gently pulling it straight out. Parts that must be dismantled from the vehicle will leave within 1-3 business days.
How long have you had yours and what engine do you have? Slide the latch to the left to release the hood and raise it. Then remove the ballast using a philip screwdriver. Posted on Feb 02, 2009 I am not sure about the Colorado, but most vehicles about that age have a plastic clip. Carefully pull back the front fascia, or molding. Had to put something behind it to get it angled properly. Push on this tab and pull the cover down to expose the bulbs. Parts that must be dismantled from the vehicle will leave within 1-3 business days.
If there is voltage there you have a problem with the new bulb. If you need anything just hollar and if you have any questions just let me know if I canhelp. If you need any assistance please feel free to give us a call at. Remember seeing that nasty-looking goo seep out from around the rubber seal on your headlights? Carefully remove the D2S Xenon Bulb from the factory housing. Then, disconnect the wiring harness from the bulb socket and remove the black retainer by turning it counterclockwise. I just replaced my headlights, I have a 2004 Touareg with 44,000 miles and have already gone through 2 sets of headlights. They have lost their minds.
You should be able to take these two clips off and the headlight will go straight forward, you can then twist the bulb holders out of the headlight assembly. Our online parts catalog uses real-time inventory, so you can be assured the parts you buy are in stock at the time of ordering. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights. Go up between the first two fender mounting bolts and look down a few inches. Locate the seam between the nosepiece and the front fender either side.
You may need an extra pair of hands to perform this slightly awkward task. There is also two screws on the top of the housing. Once you have put the ballast on, put the bracket back on. Correction: Thule will notify owners and provide a repair kit and instructions free of charge. Extended warranties are also available for purchase; please call for details. Wires is connect to the Parking lights. Now is the time to clean up the mess around the fender where the headlight mounts.
Consequence: Fuel leakage in the presence of an ignition source could result in a fire. Install the Spyder Headlight back on to the vehicle. Take a long flat head screw driver and press down toward the ground gently. Best practice is to ship to a friend or family in the Continental U. See a small knob sticking out at you? Correction: Dealers will replace the fuel tanks.
Put your headlight assembly back together by reversing the steps when you disassembled it. If you need anything just hollar and if you have any questions just let me know if I canhelp. See a tab on it? Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here. If there is voltage there you have a problem with the new bulb. Just curious if you have had any problems? Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Take out the new bulb and compare it with the one you are replacing. Correction: Dealers will replace the fuel tanks.