These bulbs have a very high voltage that runs through them, even if the battery is disconnected. Replace this assembly the same way. Place the new bulb in the hole vacated by the old bulb. Compared to a halogen low beam, a xenon low beam is characterized by a brighter and more widely illuminated road. Apr 11, 2009 It's a bulb replacement. Exposure to such oils will destroy the bulb or shorten its life. Wear eye protection for this part, because the bulb is pressurized with a caustic halogen gas that can cause eye injury.
In bi-xenon headlamps, the low beam and high beam lights are generated with just one projection module, which is mechanically switched between low and high beams via a shutter in the headlamp. Once the boot is pulled back, you will find a wire clip which holds the bulb in the socket seat. Then consult your owner's manual for the replacement procedure. You must take to dealership. Eventually opened fill plug on drivers-side of pan under car. It provides ample room and comfort for the passengers and driver. Didn't have one so used a five foot length of rubber washing machine hose I had around and a turkey baster to squirt in the hose.
If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it. Step 3 With the use of a mirror locate the spring-clip that holds in the bulb. Yeah you can, You've got the same fingers the mechanic has don't you!? If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Locate the bulb you wish to change an … d turn to release it. The passenger si … de has more room to work, so you may want to do that side first to get the feel before doing the driver's side. And two more near the back of the assembly, near the area where you would change a headlight bulb. Installation of the new one is the reverse.
You need to reach in and twist the bulb to the left and it comes out. Tools Used: Tools, Tape measure, Chalk, Clean gloves, Flathead screwdriver Adjust Headlights. I had to ask my son to do it for me. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions. The high voltage required to ignite the xenon gas: 20,000 volts: is generated by an electronic ballast.
We normally use express to do the shipment, 5-7 working days, the goods will arrive you. Raise the spare tire cover and hold it up as you pull the … carpeted panel away from the body. Once off you unclip the light from the power cable and remove the rubber cover circular that's like an end cap on the back of light housing. Then the entire headlight assembly including the turn signal can be slided out together. The complete xenon system also includes a power wash system that keeps the headlamp cover lens clean so that the xenon light is directed onto the road and drivers of oncoming vehicles do not have to contend with added glare. I did not need mechanical assistance, i. Posted on Nov 07, 2009 Dear Always use latest technology bulbs in your car headlights.
The easieast way is to raise the front of the car and remove the front wheel and tire and then remove the plasitic inner fender liner. When you change the headlight on your 545i, it is important to not touch the glass part of the bulb with your fingers because the oil from your fingertips will cause that part of the bulb to burn hotter, which significantly shortens the life of the bulb. It might be a little tight but it will come out without too much difficulty. Answer There is a big debate about this. Step 2 Remove the rubber seal directly behind the light preferable the one you want to replace. Make sure it is placed flat in the hole. Most people say that you should change it.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. In my case, it was easier to work from the inside. Install the Spyder Headlight back on to the vehicle. I was able to do it on the driver side without removing the battery. Remove the lamp from t … he holder by releasing the lamps locking mechanism and pull. The electric should just have a clip on it you can pop off directly on the rear of the exsisting bulb.
Remember to not touch the bulb itself, and follow any new bulb's directions for cleaning if you accidently do touch it. Change the bulb and reassemble. Pull out the headlamp assembly from the vehicle. If you want to re-use, be careful not to touch the glass with your fingers or any other dirty substance. On the left side when looking down into the hood , you must press it in towards yourself and then press it away from you. I can get pics if you think it will help, but it really is very simple once you know what to do.